From Disaster to Divine
Warning: MMS Milk Paint May Play with Your Emotions ;)
I'd been searching for a drop leaf table for some time, but I could never seem to find one that met my size and budgetary needs, until this one. Purchased through Craigslist (yup, another one of
my Craigslist's finds) for a mere $20, it was the perfect piece for me to experiment with the
Miss Mustard Seed Milk Paint I'd been dying to try.
Since there aren't any MMS retailers near me, I opted to buy online from the retailer who was geographically closest to me,
Sea Rose Cottage in RI (a cute shop I can't wait to visit next time I'm in the area). Since I desperately wanted to obtain the "
chippy look" (and I'm always trying to save money), I opted to risk skipping the
bonding agent (anyone see where this story's going)?
For those not familiar with MMS Milk Paint, the bonding agent is a substance that gets added to the paint in the event that the paint doesn't adhere properly to your surface (to facilitate the "bond"). So, I purchased one bag of Eulalie's Sky (the paint comes in a powder form) along with a container of
Hemp Oil. Simple enough? Well... so I thought.
When I finally got some alone time to spend with my table and my Milk Paint,
I was thrilled! I used a paint stick to mix the paint (this was trickier than I thought; I had a hard time getting all the powder to dissolve). Being used to
chalk paint, I was surprised at how thin the consistency of the milk paint was, but I had watched a few tutorial videos, so I knew I had to keep an open mind and expect a different experience.
And although I heard Marian say over and over in the videos that you can't always predict how it the paint will act, I was hoping with all my heart that my piece + my paint would = my desired chippiness.
After one coat I couldn't tell what was going to happen. It wasn't quite bubbling that much (which would indicate an area that would easily "chip"), but I did see it happening in some areas. So I decided to apply another coat... and that's when it happened. Bubbling overload.
Everything bubbled up (and consequently chipped off as soon as I touched it). And, yes, hindsight being 20-20... I should have ordered the bonding agent. Soooooo, back to the internet, another order (and another shipping charge). And this time I ordered the
milk paint mixer, too, because of the trouble I had mixing it last time (the device is basically a milk frother, so if you have an extra on hand, you could use that).
But after receiving the next package, a cold spell ensued (and the table was in the garage). So the cold, mixed with my earlier disappointment, caused the drop leaf table project to come to a halt.
Fast forward a couple months later, and I became determined to finish the project (and this time I moved the table inside). And I'm so happy (and very relieved) with the final results. Here's how it went.
 |
| I can't find my original "before" pics, so this is the closest I can get. This is between "Take 1" and "Take 2." I actually sanded the top after the first debacle, so it originally looked a little darker than this. | | |
Steps for Painting the Drop Leaf Table with MMS Milk Paint (and an ASCP Stripe)
- Mix the paint (and in my case, add the bonding agent). I recommend using the electric frother-mixer.
- Paint! And paint some more. The paint is thin (although you could adjust this by adding less water, but I didn't have much to work with, so I was stuck with what I had)! After reading the directions, but after mixing the paint (yea, in general, I tend to have some trouble following directions), I found out that you only need to add the bonding agent on the first coat. But I had already mixed it all together (because I only had about half a bag of powder left). So the bonding agent was in the paint for each coat. My mix lasted me about three coats (although certain parts could have taken another coat, but I wasn't going to buy a whole new bag for that).
- Add the stripe. Although I was happy with the color of the paint, I thought the table was a little boring, so I decided to add a stripe. I had Annie Sloan Chalk Paint in Pure White on hand, so that's what I used. I wanted the stripe to be subtle, so I watered down the paint and only applied a thin coat.
- Distress. As Marian suggests in her videos, I used a paint scraper to distress the table. Although I had to work pretty hard at it (that bonding agent sure did its job!), I still liked this process SO MUCH better than using sandpaper or nail files (that's what I used on my Distressed Dining Table). I just can't stand how HOT the sandpaper/files get because of the friction when you're working... it gives me stomach-churning goosebumps, the way some people feel about fingernails on a chalkboard. Yuck. I don't even like thinking about it. Soooooo the paint scraper was the best idea I've heard in a while! Nice plastic handle = no friction on my fingers!
- Apply the Hemp Oil. This was my favorite part! I used a cut up old tee-shirt to apply the wax, and the consistency was so nice. As soon as it touched the paint, a lovely hue emerged, making me soooo happy. Before this step I was doubting I'd use MMSMP again, but after using the hemp oil (and a little experience behind me), I think I'm going to give it all another shot! I followed the instructions and wiped the excess oil off after 30 minutes.
So there you have it... I never knew a paint would have the ability to
make me cry, cringe, smile, and shout, but I guess you learn something
new every day :) I'll be using the table in our upstairs hallway as our new
laundry-folding station (to replace the current "station": B1's bed! Now I don't have to feel guilty if I don't finish folding all the laundry by bedtime!).
 |
| Here's one of my laundry helpers ;) |
 |
| Top View: I'm so happy I added the stripe! |
Have you used Milk Paint? What have you used it for? Do you like it? After all this, I need someone to commiserate (and celebrate) with ;)
Follow along on
Pinterest and
Instagram for more of my DIY adventures!
Featured On:
